MrHiggles

So here is a list of what I have and what I plan to get.

Racingline- Y-pipe, Sway Bar, Front Strut Bar
Borla Mufflers
DEPO LED Tails (black)
EBC Rotors and Red Stuff Pads (front for now)
Takeda SRI
Interior LED (drivers side light went out and replacements wont work :/ help? )
Nismo Rear Spoiler

What I want:
Enkei RP03 rims or Volk TE37s Replicas. (or any nice black rim)
Black out trim
C-Mod or just a nice mesh black grille
Intake Spacers
Block off place
Vibrant MAF sensor
Vibrant Throttle body (if I can)
Something to tune the car (help)
Maybe coil overs or lowering springs.
8" subs x2 (good brand) and amp
Racingline Grounding Kit
Longer lug nuts cause my lug wrench scrapes the inside of the rims.
Might paint the calipers
Tinted head lights

Also can I put vinyl tape on the amber part of the head light to make it look like a eyebrow?

(0)

mikejamesbyma

What's your thought wih the throttle body?

I think you should move the BOP plates and spacers to the top.

__________________

03 Altima 3.5
4AT, Muff delete,
ebay CAI w/AEM filter
vias mod
Vogtland springs/KYB GR-2/Godspeed camber arms
Transgo RE4F04B-HD2
- (valve body removed)

(0)

black05alti

I think you should lower it next, then BOP plates and spacers, then wheels!

__________________

(0)

MrHiggles

Lol that list wasn't in order

__________________

(0)

Unclear_Motives

Which led lights do you have that aren't working? In the drivers door?

__________________
Just call me Ray
READ-THIS: AWESOME INFO!

twitter: @Unclear_Motives
email: Unclear_Motives(at)Yahoo

(0)

MrHiggles

its on the door. It lights up just as u open it to light up the ground. Its where the kick plates are located

__________________

(0)

Unclear_Motives

Here's a trick we use here:

Pry the tiny wires away from the bulb housing a bit, to allow them to make good contact with the metal on the door housing.

If it doesn't light up when you put it back in, pull it out, and twist the bulb 180 degrees before putting it back in.

The positive and negative may not be in the right spots.

__________________
Just call me Ray
READ-THIS: AWESOME INFO!

twitter: @Unclear_Motives
email: Unclear_Motives(at)Yahoo

(0)

blazerk5drew

What is this throttle body and maf sensor you speak of? Im trying to find a way to get a maxima intake which uses a larger tube to work with my maf sensor. when installed, it throws lean codes.

(0)

mikejamesbyma

You will need a tuner to run a larger MAF tube. You can see good gains with it, but you will need to add fuel to get it to run.

You should check out Apexi. Not cheap but it will fix your issue.

http://apexi-usa.com/

__________________

03 Altima 3.5
4AT, Muff delete,
ebay CAI w/AEM filter
vias mod
Vogtland springs/KYB GR-2/Godspeed camber arms
Transgo RE4F04B-HD2
- (valve body removed)

(0)

blazerk5drew

Is this what Id be looking at? http://apexi-usa.com/shop/index.php/...s/afc-neo.html

Im very interested. I just dont know what step to take next. I havnt heard a whole lot about tuning on the 07 and up cars. I think I need to get the vias plates in first and then go for the tuning device.

When i had the intake for the max installed. It seemed to run ok but after a day or two the CEL came on. I dont want to throw upwards of 600 bucks into something for 10 hp. It was much easier with older cars I had that I could just order a reprogrammed ecu based on my mods for a couple hundred bucks and they worked rather well.

(0)

mikejamesbyma

That's the one. You'll have to do some searching to find out about it's use with the new generation. It has the ability to fix your lean condition, as long as it will work with your generation.

__________________

03 Altima 3.5
4AT, Muff delete,
ebay CAI w/AEM filter
vias mod
Vogtland springs/KYB GR-2/Godspeed camber arms
Transgo RE4F04B-HD2
- (valve body removed)

(0)