Nissan Altima Forum banner
41 - 60 of 72 Posts
I guess I have a different problem then. I changed the relay switch first $30.00. Still nothing! Had new blower motor put on $200.00 still nothing! Now what? My car takes about 15-20 before it starts blowing. If I turn off the car, I have to wait another 15-20 minutes. Now it stops blowing by itself! Have checked fuses and they seem to be good. Nissan really needs to have recall on this problem!!!!!
nissan should have a recall on this problem, it figures my warranty just ran out last month
 
wonder if having a cracked serpentine belt complicates the issue. I also thought my a/c compressor was going out as I tried one of those quickie R134a refrigerant refill kits, but no go.

After I replaced my cracked serpentine belt, my a/c comes on instantly and actually a little TOO cold!

The blower motor might be cheaper than Napa auto parts if you go to rock auto.com



 
I typically do not post comments to "expert" forums such as this as I am admittedly not real proficient in terms of my car knowledge. But with that said, I felt compelled to share my experience here as I know there are probably many others like me who would have gotten fleeced by a dealership to diagnose and repair what is, evidently, a not uncommon, yet very fixable and affordable solution.

Although I'm in Texas, my first sign of an issue (in late 2011) actually involved my heater as it would not blow hot air (or any air for that matter) until the engine was warm (anywhere from 10-20 minutes). Well, because it's Texas, this was more of an inconvenience than a full-on emergency, however it signified the beginning of my many months of fighting through what was clearly not as dire a situation as what many non-auto experts probably fear.

Throughout these many months, I came to realize that the issue would not just go away and as a result, it became increasing more intolerable as the summer heat arrived. While now affecting the a/c, the diagnosis was the same - the a/c would not kick on until several minutes into my trip (when the engine was warm). Thankfully, the hotter it was outside, the quicker it came on. And I should note that the heater and a/c worked perfectly once it actually began to work.

While my frustration really began to mount, I started to resign myself to the fact that the only solution would be to take it to a dealership to try and repair. What gave me great pause, however, was the relative ignorance I got from each dealership. I explained the problem to several different service technicians and was given no assurance by any that my issue would be remedied for anything less than hundreds of dollars. It was the same old line..."bring it in and we'll take a look at it"...the kiss of death for someone on a budget, who knows nothing about cars.

With my back against the wall (and two months of 100+ degree temperatures looming), I came across this forum. I read and reread each post in this thread a dozen times before I finally decided to take the matter into my own hands. While I never understood the technical aspect of the repair as it related to the problem, I felt like I needed to at least try to do it myself as each testimony seems to corroborate the issue I was having. And lo and behold, it worked...this car idiot fixed it.
Anyway, while the previous posts do a great job of explaining how to perform the repair, I wanted to give a step by step instruction for those, like me, who are intimidated by simply raising the hood. The mere fact that I was able to diagnose (thanks to this site) and carry out the repair (thanks to this site) is proof positive that anyone can do this...and not somehow make the problem worse. Here it goes:

1) On the driver's side, remove the fuse box cover below the trunk release and above the hood release.
2) Inside the area of the fuse box, unscrew (with a phillips head) the knee board that runs across the entire driver's side (under the steering wheel). Note: even though this is a rather large panel, there is but one screw that keeps it in place.
3) Disconnect the knee board that you just unscrewed. This panel sort of unsnaps and will hang under the steering wheel. There is a small side panel that will unsnap as well.
4) With pliers (or a wrench), unscrew the three screws that hold the fuse panel in place...the relay that you are trying to get to is on the backside of the fuse panel. In my 2007 Altima, there are two screws right next to each other and a third up and to the right. Once you have unscrewed the fuse panel, it will give you some mobility, but the backside of the panel (where the relay lies) is still pretty hidden. The relay itself (which hopefully you have already purchased) looks like a little ac adapter plug (for lack of a better description). I ordered mine from a Napa Auto Parts by telling them I need a blower motor relay, part #2523079942. It was $26.99 and delivered to my local store on the same day I ordered it. They will probably tell you that it is a non-refundable part, so they'll ask you if you are sure it's what you need. At this point, I became a tad nervous, but persisted as thirty bucks seemed like far cry from the hundreds I'd perhaps be facing by settling on the dealership. Anyway, if you've encountered the same issues as detailed previously in this thread, this purchase is worth the try.
5) Once you have relay in hand, you should be able to see something similar on the backside of the fuse panel. With flashlight in one hand, you should be able to shimmy out the (bad) relay on the far left of the backside of the fuse panel. It will "unplug" from the location closest to the driver's side door. Note: as you unplug it, take note of the position of the prongs upon its release. This will aid you when you "plug in" your replacement.
6) Once you've removed the old and replaced the new, I recommend starting the car to see if you've been successful. It was at this point that I began to sing to the heavens for introducing me to this forum.
7) Hopefully, you are experiencing the same relief as I at this point and simply now need to screw back in the four screws that got you here.

For you car/Nissan aficionados, I apologize for this "dumbed down", lengthy post. But that said, I'd love to know that perhaps just one other person (much like me) was able to gain some insight without throwing hundreds of dollars at the problem.
My 07 altima got the same problem. I stupidly sent it to the nissan dealership, they costed my 130 dollars to check it and then suggest me to replace the climate control unit by paying around 400 dollars. I really doubted it. So I did not go with it. I found this post and follow the detailed instruction and I made it within an hour. I did not replace the relay, instead I switch the air conditioner's relay with the one next to it, which is the radio relay.Now My car's air conditioner is working properly. And, my radio is fine too. And I did not spend a peny on it. Thank you for sharing this very helpful information. It save me lot of money and time.
 
Thanks!!

Hi all, just wanted to say as mechanically inept as I am I was able to follow the step by step directions and managed to fix this issue myself.

Thanks for this, amazing work helping newbies like me save the time & annoyance of a dealership!

Much Appreciated!
 
Ok, first, thank you everyone and especially Zeinertom. His thread gave me the last piece of confidence I needed to get this done. My posting is first to say thanks, and then also to help others find this thread....cause it was right on. I started trying to bleed the air from the coolant system (and broke the cap following those directions, as well as a screw.....yes it was cold).

Anyways, symptoms to aid in google searches:
my girl's 2008 Nissan Altima heat not blowing for 20 minutes, heat not blowing until I drive for a while, blower doesn't come on right away, car is heated up but blower doesn't come on, replace blower relay,

Zeinertom nailed it all the way, his description was perfect. I'm going to attempt to add some pictures to help even further, because I don't want people getting raped by a dealership for something this inexpensive to fix.

So, read Zeinertom's post very carefully. It's well written. I used a small ratchet (5/16") for the two screws holding together holding fuse box, and a straight 5/16" screwdriver bolt thing for the top one.

Now, this is after I struggled popping the knee board....I didn't want to break her car!

I've attached pictures....the first is just a pic of the fuse panel. That's the right place.
The second is the blower relay and number on the box.
The third was a shot from laying upside down with my head hitting the break pedal. I still didn't know where to find the blower relay yet, but it indeed was one of those blue ones. (closest to the door is the good clue). That's the back of it. Maybe a petite gal with tiny hands not working in the winter could get in there without dismantling the panel, but good luck.
The 4th picture is from outside the car after I successfully ripped apart the dash. JK, but this one has a piece that pops out to the left first, or it will launch off when you pull hard enough on the dash piece. Zeinertom is correct, one screw. You can see the blue blower relay closest to you...that's the small part that you'll pay $30ish for and probably save hundreds.....

Thanks again.

Good luck, everyone!

Fatty
(Don)
 

Attachments

Thank you for the "dumbed down" write up! I couldn't figure out where the 2nd screw was. Reading through your walkthrough clarified that there was only 1 external screw holding the entire panel in place! Just completed the swap and we now have heat!!! Yesssss!
 
My thanks to Zeinertom for the more detailed write-up! Some additional details to the instructions quoted below

You will need to remove three ~8mm nuts from the inside the fuse box. An 8mm socket with an extension works well. Alternatively, use a needle-nose pliers to turn your 8mm socket and remove the nuts (I was too lazy to go back into the house for a socket extension). You might be able to do this with pliers alone, but one of the bolts in my car was too tight for this. And it would be tough to get a wrench in there.

Orientation of the relay "plug": The horizontal prongs will be on the top. I'd post photos, but I don't have enough posts on this board yet.

Fatty's photos and additional tips are helpful. I wish I could annote them with some numbers/text and upload them. Or post my own. But I don't have enough posts on this board yet.



Zeinertom's instructions plus minor modifications in brackets:
1) On the driver's side, remove the fuse box cover below the trunk release and above the hood release.
2) Inside the area of the fuse box, unscrew (with a phillips head) the knee board that runs across the entire driver's side (under the steering wheel). Note: even though this is a rather large panel, there is but one screw that keeps it in place.
3) Disconnect the knee board that you just unscrewed. This panel sort of unsnaps and will hang under the steering wheel. There is a small side panel that will unsnap as well. [This plastic "end cap" panel is essentially next to the door hinge.]
4) With [8mm socket and extenstion OR 8mm socket plus needlenose pliers], unscrew the three [bolts] that hold the fuse panel in place...the relay that you are trying to get to is on the backside of the fuse panel [top left, nearest driver's door]. In my 2007 Altima, there are two screws right next to each other and a third up and to the right. Once you have unscrewed the fuse panel, it will give you some mobility, but the backside of the panel (where the relay lies) is still pretty hidden. The relay itself looks like a little ac adapter plug (for lack of a better description). I ordered mine from a Napa Auto Parts by telling them I need a blower motor relay, part #2523079942 . [Also available on Amazon]
5) Once you have relay in hand, you should be able to see something similar on the backside of the fuse panel. With flashlight in one hand, you should be able to shimmy out the (bad) relay on the far left of the backside of the fuse panel. It will "unplug" from the location closest to the driver's side door. Note: as you unplug it, take note of the position of the prongs upon its release [horizontal prongs at the top]. This will aid you when you "plug in" your replacement.
6) Once you've removed the old and replaced the new, I recommend starting the car to see if you've been successful.
7) Hopefully, you are experiencing the same relief as I at this point and simply now need to screw back in the four screws that got you here.
 
I have the problem with the fan coming on very late on my 2007 Altima - usually after 20 minutes. This is not good for winter driving.

That was a 30 minutes job to install the new relay. The instruction was 100% accurate. The toughest part was to remove the old relay.

I installed OEM relay and it doesn't work - very disappointed!!!

Any suggestion?
 
Thanks guys I had the same problem with 2007 Nissan altima. Went to the dealer and they charge me 60 just to inspect it and told me to change the climate control head/unit and it would cost me 600 including labor. I order a used climate head on eBay for 20 and replaced the old one and nothing... and then replaced the blower motor for 150 and Nothing!! And finally I got online and luckily saw your post on the blower motor relay. So I ordered it and replaced it myself in like 20 min and boom!! Got it fix!!! Thank you all soooo much!!!
 
I have another problem in my 2010 Altima base model, which looks related to blower motor, it will turn on fine (fan speed set to 50% or lower), however, after 5-10 minutes, air flow will slow down gradually then stop flowing. When this happens, i turn the fan control to max then air starts flowing again, then i lower it again because its too high, after 5 or so minutes, air flow slows down and gradually stop again.

Is it the relay or something else? Did anyone experience this?
 
2015 Altima blower not working

The AC blower on my 2015 Altima is not blowing any air. Checked the fuses and both of the blower motor fuses were open. I replaced the fuses and both failed immediately. I pulled out the blower motor, replaced the fuses, then checked the voltage at the blower connector. It is 12-14 volts between the two big terminals, regardless of the position of the control knobs. Not sure what the third smaller terminal on the motor is. The motor rotates easily. The resistance reading across the two bit motor terminals was 0 ohms.
I connected the motor directly to the battery and it spins (although there is a slight smell of burnt electronics in the blower motor). The resistance across the motor terminals is now more like 1 or 2 ohms.
Connected the motor back to the wiring harness again just for fun and blew both fuses again. I'm thinking blower motor may be bad. Anyone have any ideas? Also, what is that third terminal on the motor? I assumed it was some sort of speed control signal, but it doesn't seem to vary at all when I turn the knobs (with the blower disconnected).

Hopefully I'm posting this in the right place. First time posting here.
 
The same thing is happening to me... I have replaced the blower, the relay and the control (used control form ebay) and it still does this. I have checked the diverter actuators and the fresh/recerc, hot/cold and face/foot/defrost all are working properly. I am not sure if it the climate control that I swapped out was bad or what...
 
Sorry, replying with the quoted text isn't working...

in reference to:

I have another problem in my 2010 Altima base model, which looks related to blower motor, it will turn on fine (fan speed set to 50% or lower), however, after 5-10 minutes, air flow will slow down gradually then stop flowing. When this happens, i turn the fan control to max then air starts flowing again, then i lower it again because its too high, after 5 or so minutes, air flow slows down and gradually stop again.

Is it the relay or something else? Did anyone experience this?


The same thing is happening to me... I have replaced the blower, the relay and the control (used control form ebay) and it still does this. I have checked the diverter actuators and the fresh/recerc, hot/cold and face/foot/defrost all are working properly. I am not sure if it the climate control that I swapped out was bad or what...
 
in reference to:

2015 Altima blower not working

after lots of research I discovered that the Altimadoesn't use normal voltage changes for the fan, actuators, etc.. It is using a special "network" kind of like a computer network to signal all the actuators and blower motors. the tiny wire attached to the blower (not the ground or positive) is a signal wire which tells a micro-processor inside the blower what speed to spin. the same goes for the actuators, the small wires signal the actuator motor what position to be in.
 
blower works but not always

Hey guys, i have this problem with my altima 07, the blower and the radio is working fine but, when i go to work and let my car under the sun for 4 or 5 hours at(40°c or 104°f culiacan,mexico) the blower and the radio just dont turn on anymore. ::crying:: . When i got home and my car its under roof, fresher than outside, the blower and the radio turn on in about 1 hour. I changed the blue relays all of them and got nothing, checked the fuses and seem fine. I also carried my car to electricians and they didnt find nothing.!! I just need to wait till my car is "fresher" and everything is fine again. Any idea? Could it be the motor blower? How can i get to it? is there kind a termostate or resistance that i need to replace? Id apprecciate your help.

Sorry about my english.
 
AC blower issue

I didn't see a follow up to this question- as I am now experiencing the same issue as Nolimits- but I have a 2008 Altima. Would the Blower Relay fix this issue described (quoted below)? Thanks in advance- Robert


I have another problem in my 2010 Altima base model, which looks related to blower motor, it will turn on fine (fan speed set to 50% or lower), however, after 5-10 minutes, air flow will slow down gradually then stop flowing. When this happens, i turn the fan control to max then air starts flowing again, then i lower it again because its too high, after 5 or so minutes, air flow slows down and gradually stop again.

Is it the relay or something else? Did anyone experience this?
 
I made an account on here after replacing the blower motor relay as you guys all recommended! I cannot thank y'all enough as my heat started blowing immediately after the replacement when I turned my car on. It's currently -15 here in Ontario, Canada so this fix has me so stoked. Thanks again to everyone who gave detailed instructions. I could have went to the dealer and wasted god knows how much moulah but instead all I needed was a 40 CAD part from NAPA. I also just want to theorize that this relay part could become faulty due to it's position compared to the other relays. It is the relay closest to the outside of the car and therefore the elements. Different temperatures affect it's function because my heat would work (after 20 minutes of driving) when it was above 4 degrees C but as soon as it was colder than that I had no help in hell of not freezing my ass off while driving. Thanks again guys this was a ----in lifesaver
 
41 - 60 of 72 Posts